1: What type of speakers work best with with T20X Amplifier?

• Fosi Audio Amplifiers work great with any 2-8 ohms passive speakers. You can connect passive speakers via the Speaker Output or active speakers via the Headphone.

2:  Can I connect a turntable to T20X amp, why is the volume is extremely low?

• As for the turntables do not have a built-in preamp, you need to add an external phono preamp before connecting T20X, such as our BOX X1, or BOX X2.
• As for the turntables which have a built-in preamp, the switch must be set to LINE before connecting T20X.

3: Why does the sound is cracking or make a lot of electric noise?

• Please make sure all the cables completely pushed into the devices, incompletely connection will cause this cracking.
• Please remove all the inputs then check whether cracking noise disappear or not, the cracking maybe from the audio source or input cables.
• If you are not using the original factory standard power supply, please replace the power supply before testing. Many power supply in the market have large interference coefficient, which will cause a lot of current sound.
• Please check if the vacuum tube is completely plugged in, and try to change the left and right vacuum tubes.

4: My Bluetooth device cannot pair with T2OX?

• Make sure that T20X is powered on.
• Make sure that T20X is not paired with other devices.
• Make sure that the distance between your device and T20X is not too long.
• Make sure there are no barriers between your device and T20X, barriers will affect the Bluetooth operation distance.
• Please reconnect the power supply to the T20X, and move the T20X to another room to have a try.
• Restart the T20X and then try to connect again, try to use another Bluetooth device.

5: Why Bluetooth is intermittent?

• Please try with another Bluetooth device.
• Make sure there is no interference from other electronic devices between the T20X and the audio device.
• Place your device close to the T20X, and plug in the power adapter again.

6: How much power does it take in standby mode? Can this amp be left on all the time?

• This is the class D amplifier, it will cost very low power when it is in standby mode. It can be connected all the time and it is safe without power consumption.

7: Sound quality is not good?

• Make sure all the cables are fully connected.
• Adjust the treble and bass control of the power amplifier to achieve the right tone.
• Please try to change the sound source and cables to test.
• Please check if the vacuum tube is broken or completely plugged in.

8: Can T20X accept signal from a Bluetooth microphone?

• Please make sure your Bluetooth microphone must be the transmitter. Because T20X is a Bluetooth receiver amplifier.
• Please make sure that microphone's Bluetooth can be connected to the T20X's Bluetooth by your operation.

9: Why does the sound cut in and out?

• Please try to change the sound.
• Lower the treble and bass of the T20X.
• Make sure that the positive and negative terminals of the speaker outputs do not touch each other. Some of the larger banana plugs can easily touch each other and cause a short circuit.

10: Can I bridge channel 1 and channel 2 to get 2O0watts?

• No, this amplifier can't be bridged.

11: Why does distortion occur?

• Because the vacuum tubes amplify the sound. If you turn the sound up too loud, distortion may occur. Please try turning the volume down a little.

12: Can I replace the vacuum tubes?

• If necessary, there are substitutions: EF95, 6AK5, 6AK5W, 403A/403B, 6J1, 6J1P, 6J2, 6J3, 6J4, 6J5 vacuum tubes, You can replace the vacuum tubes to DIY your stereo system.

Note: Please must remember switch off the power BEFORE you pull out the tube, or it might damage the device.

13: Why the T2OX came with a broken vacuum tube?

• Due to the long-distance, the vacuum tube may be damaged during transportation. If you find that the vacuum tube is broken or there is other problems, please contact our email, and we will replace the vacuum tube for you.

14: Can headphones and speakers play at the same time?

• Yes, once the headphones plugged in, it could play through headphones and speakers at the same time.

15: How can I connect T20X to TV?

• The RCA jack is the audio input. It can through RCA input to connect your TV.

16: Why there is no voice from my amplifier?

• Please check whether the cable of power supply is connected to T20X and whether the power indicator is on.
• Make sure the T20X's indicator light is on when the power is turned on.
• Please check that the T20X and your source components are turned on and not set to minimum volume, if possible replace your source and test again.
• Check that the wire connections from the audio source to each speaker in the amplifier are connected correctly.
• Please check that the cable is not loose, Incomplete connection is one of the main reasons for no sound.
• Please make sure the Bluetooth is paired or not, if Bluetooth is connected, AUX input will be disconnected. If you want to connect this amplifier with a 3.5mm AUX cable, you need to disconnect the Bluetooth first.

17: Can I use Bluetooth head phones with this unit?

• This tube amplifier is a Bluetooth receiver, not a Bluetooth transmitter. It works with 3.5mm wired headphone